Rebar Support Chairs / Mesh Chairs
Paragon's Rebar
Support Chairs
can be used for at grade or precast applications with the use of #3 through #5 rebar or post-tension cable.
|
 |
- Rod snaps easily
into chair
- Wide base allows
Rebar support chairs to stand securely
- Eliminates wire
tying
- Non-corrosive
durable polypropylene
- Non-conducive,
perfect for bridge decks
|
|
With Base
| Part No. |
Size |
Bar Size |
Qty./Ctn. |
Wt./Ctn. |
| 1202-0001 |
3/4" |
3-4 |
3000 |
29# |
| 1202-0005 |
1" |
3-4 |
2500 |
23# |
| 1202-0007 |
11/2" |
3 |
800 |
30# |
| 1202-0010 |
1 1/2" |
3-6 |
800 |
30# |
| 1202-0015 |
2" |
3-5 |
500 |
21# |
| 1202-0025 |
2 1/2" |
3-5 |
500 |
25# |
| 1202-0030 |
3" |
3-5 |
500 |
25# |
| 1202-0035 |
31/2" |
4-5 |
500 |
27# |
| 1202-0040 |
4" |
4-5 |
325 |
30# |
| 1202-0045 |
4 1/2" |
4-5 |
250 |
30# |
| 1202-0050 |
5" |
4-5 |
250 |
32# |
| 1202-0055 |
5
1/2" |
6 |
225 |
32# |
| 1202-0060 |
5 1/2" |
6 |
168 |
30# |
|
1202-0065 |
6" |
4-5 |
120 |
30# |
| 1202-0066 |
6" |
6 |
120 |
25# |
| 1202-0070 |
6 1/2 " |
6 |
100 |
|
| 1202-0075 |
7" |
4-5 |
100 |
32# |
| 1202-0076 |
7" |
6 |
100 |
25# |
|
No Base
|
Part No. |
Size |
Bar Size |
Qty./Ctn. |
Wt./Ctn. |
| 1202-0500 |
3/4" |
3-4 |
4000 |
22# |
| 1202-0505 |
1" |
3-4 |
2500 |
20# |
| 1202-0510 |
2" |
3-5 |
800 |
21# |
| 1202-0515 |
2 1/2" |
3-5 |
800 |
25# |
| 1202-0520 |
3" |
3-5 |
550 |
25# |
| 1202-0525 |
3
1/2" |
3-5 |
550 |
27# |
| 1202-0530 |
4" |
4-6 |
500 |
30# |
| 1202-0535 |
4
1/2" |
4-6 |
400 |
30# |
| 1202-0540 |
5" |
4-6 |
350 |
32# |
| 1202-0545 |
5
1/2" |
4-6 |
325 |
32# |
|
Paragon's Products
rebar support chairs
have been tested and approved by
the Iowa Department of Transportation, office of materials division, and
either meet or exceed the load carrying capacity of steel supports and can
therefore be used at the same spacing as wire supports.
Installation:
Only laborers who are
experienced with steel reinforcement placement, should install rebar
support chairs. Maximum spacing of chairs should not exceed 48
inches. Comply with applicable codes and design criteria for minimum
spacing of reinforcement from edges of forms.
Testing Procedure:
This testing procedure involves determining a point load limit for all
supports. The point load is determined by placing a piece of #4
rebar on the support. the support is then placed on a 3/4" thick
piece of fir plywood. A load is applied to the 1/2" deflection per
minute until the support fails. Point loads are determined at the
weakest point on continuous supports.
Results:
| Chair
Sizes |
Maximum Load
(lbs.)
|
| 1 1/2" |
|
1085 |
| 2" |
|
1400 |
| 2 1/2" |
|
1146 |
| 3" |
|
1062 |
| 3 1/2" |
|
1199 |
| 4" |
|
1150 |
| 4 1/2" |
|
349 |
| 5" |
|
384 |
| 5 1/2" |
|
403 | | |
|
|
Paragon's
Mesh Chairs are designed to support 6-10 gauge
mesh. Snap-in top allows panels to be moved without chairs falling off |
 |
|
- Mesh Chairs round base provides stable support on grade
|
| Part No. |
Size |
Gauge Mesh |
Qty./Ctn. |
Wt./Ctn. |
| 1202-1000 |
2" |
6-10 |
800 |
22# |
| 1202-1005 |
2
1/2" |
6-10 |
500 |
25# |
| 1202-1010 |
3" |
6-10 |
600 |
22# |
| 1202-1015 |
3
1/2" |
6-10 |
500 |
25# |
| 1202-1020 |
4" |
6-10 |
350 |
30# | | |
| Paragon's
Large Rebar Support Chairs are designed to support
heavy reinforcement in foundations, heavy slabs, and special
structures. |
|
 |
These chairs will accept any
bar diameter and can be easily wire tied. |
|
Part
No. |
Size |
Bar Size |
Qty./Ctn. |
Wt./Ctn. |
| 1202-1500 |
4" |
Any |
130 |
30# |
| 1202-1505 |
5" |
Any |
100 |
30# |
| 1202-1510 |
6" |
Any |
100 |
30# |
| 1202-1515 |
6
3/4" |
Any |
100 |
30# |
| 1202-1520 |
7" |
Any |
100 |
30# |
| 1202-1520 |
8" |
Any |
100 |
30# | | |
More About Us…Paragon Products specializes in concrete and rebar accessories such as rebar safety caps, concrete test cylinders, hog slat chairs, spacer wheels, pocket formers, tilt-up chairs, and hole-in one covers for commercial, highway, and pre-cast construction markets. |
